fill my day Coming to BristolComing soon

PLUMBING PROBLEMS

Low water pressure: what to check first

How to work out whether weak water pressure is your plumbing or the supply, the checks that take five minutes, and who to call.

IN SHORT

Start by asking a neighbour: if their pressure is low too, the problem is probably on the water company's network, and it's theirs to fix. If it's just you, check your stop tap is fully open and do a one-litre flow test at the cold kitchen tap. Water companies should supply at least 7 metres of head, about 0.7 bar, to the edge of your property. Anything inside is yours, and a plumber's job.

FIVE-MINUTE CHECKS

Before you call anyone.

In the order Bristol Water suggests.

01

Ask a neighbour.

Low for them too? It's likely the network, not your pipes.

02

Check for works.

Your water company's map shows planned and emergency work nearby.

03

Open the stop tap.

Turn it off and on a few times. A half-closed stop tap is a common cause.

04

Time a litre.

From the cold kitchen tap, with everything else off. Under 7 seconds is normal.

This page is part of our guide to common plumbing problems. It's general guidance for homes in England and Wales.

Signs your water pressure is low

Low pressure usually shows up in everyday things before you think to measure it. CCW, the independent body for water customers, lists these signs:

  • The shower drops to a dribble when someone flushes a toilet or turns on a tap.
  • The bath takes much longer than about five minutes to fill.
  • The toilet cistern takes a long time to refill after a flush.

It's worth noting when it happens. Low pressure at busy times of day points to demand on the network. Low pressure all the time points to something in your own pipes.

The checks to do first

These are the steps Bristol Water suggests, and they apply anywhere.

  1. Ask a neighbour

    If their pressure is low too, the cause is probably on the water company's network. If theirs is fine, it's more likely your own plumbing.

  2. Check for works nearby

    Water companies publish maps of planned and emergency work. A burst main down the road can drop pressure for a whole street.

  3. Check for frozen pipes

    In cold weather, look for frost or condensation on pipes in lofts, garages and outside walls.

  4. Work the stop tap

    Turn the stop tap off, run a nearby tap, then turn it back on by the same number of turns. Do this a few times. If it's stiff, stuck or broken, call a plumber rather than forcing it.

  5. Time a litre

    With every tap and appliance off, fill a one-litre jug from the cold kitchen tap. Bristol Water says under 7 seconds is normal.

If the cold kitchen tap is fine but other taps are weak, the problem is almost certainly inside your home.

Your pipes or the water company's?

Responsibility splits at the outside stop valve, usually under a small cover near the edge of your property. CCW explains it like this:

  • The water company owns the pipe from the main to the outside stop valve, and has to keep pressure up to that point.
  • You own the supply pipe from there into your home, whether it's shared or not, and all the plumbing inside.

CCW says Ofwat expects water companies to maintain at least 7 metres of static head, about 0.7 bar, in their pipe. Bristol Water says it aims for 10 metres, about 1 bar, where its pipe meets yours.

If you think the supply is the problem, CCW suggests keeping a record of when pressure is low over a couple of weeks, then asking your water company to visit and test it.

Common causes inside the home

  • A stop tap or valve that isn't fully open. Often after earlier work.
  • A leak. Water escaping somewhere lowers pressure everywhere else. See leaks under the sink.
  • Old or furred-up pipes. Older iron pipes and limescale both narrow the pipe over time.
  • How the system is set up. Homes fed from a tank in the loft usually have lower pressure upstairs than homes fed directly from the mains.
  • A clogged aerator or shower head. If only one tap or shower is weak, unscrew and descale its end first.

When to call a plumber

Call a plumber if the problem is inside your property and the simple checks haven't fixed it, or if the stop tap is stuck. Finding the cause usually means testing pressure at different points and looking at the pipework, which is often an hour or so of work. Our guides to call-out charges and hourly rates explain what that costs.

Fill My Day is coming soon to Bristol. It's for jobs like this that need a plumber but not in the next hour, and sends them to checked plumbers nearby with free time. It isn't taking bookings yet. See what's launching in Bristol.

Where this comes from

GOOD TO KNOW

Questions,
answered straight.

Who is responsible for low water pressure?

It depends where the problem is. CCW, the water consumer body, explains that the water company is responsible up to the outside stop valve. The supply pipe from there into your home, and everything inside, is yours.

What is the minimum water pressure in the UK?

CCW says Ofwat expects water companies to maintain at least 7 metres of static head, about 0.7 bar, in their pipe. Bristol Water says it aims for 10 metres, about 1 bar, where its pipe meets yours.

How do I test my water pressure?

Bristol Water suggests filling a one-litre jug from the cold kitchen tap with everything else turned off. Under 7 seconds is normal. CCW says a bath should take about five minutes to fill.

Why is my water pressure low only upstairs?

If the kitchen tap is fine but upstairs taps and showers are weak, the problem is in your own plumbing. It may be the way the system is set up, a partly blocked pipe or a valve. That's a job for a plumber.

FIRST STOP / BRISTOL

Bristol.
You’re up first.

The app is in development and isn't taking bookings yet. Plumbers first, other trades to follow.